SKU: SCC145120410
The Victron SmartSolar 450/200, part of the SmartSolar MPPT RS series, is engineered to effectively handle substantial series-connected PV arrays when charging 48V DC battery banks. Tailored for medium to large off-grid systems, this product offers an efficient solution for maximizing solar power usage.
MPPT: Ultra Fast Maximum Power Point Tracking
The SmartSolar RS solar charge controller connects to a PV array of between 80 and 450 Volt Voc and will efficiently charge your 48V battery bank with either 100A or 200A.
The charge settings are fully programmable and can be set up for different battery chemistries, like lead-acid, lithium and more.
Setup and monitor with VictronConnect
The SmartSolar RS charge controller can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, historical data and trends.
Daisy Chain Additional Units
The SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows for communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply “daisy chained” to each other with an RJ45 cable.
When connected to each other, all individual charge controllers, will synchronise their charge stages. They can also send their data, via the same cable, for monitoring to a GX device (such as the Cerbo GX).
Remote Monitoring and Control
If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your SmartSolar RS charge controllers.
If your installation is connected to a GX device and the internet, Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; for free.
For remote installations - even when there is no internet connection nearby - you may be able to monitor your MPPT by connecting the GlobalLink 520.
SmartSolar Display
The SmartSolar RS charge controller is equipped with a display on the front panel. The display reads battery volts, charge current and voltages from both array’s individually including instantaneous and total figures and unit status including any possible error
I/O Connections
The SmartSolar RS charge controller is equipped with a programmable relay and options for remote temperature and voltage sensing. The remote input can accept the Victron smallBMS and other types of BMS with allow-to-charge signals.
Battery voltage | 48 V |
Rated charge current | 200 A |
Maximum charge power |
11,5 kW at 57,6 V
|
Charge voltage 'absorption’ |
Default setting: 57,6 V (adjustable)
|
Charge voltage 'float' |
Default setting: 55,2 V (adjustable)
|
Programmable voltage range |
Minimum: 36 V Maximum: 60 V (7)
|
Charge algorithm |
Multi-stage adaptive (adjustable)
|
Battery temperature sensor | Included |
Maximum efficiency | 96% |
Self-consumption | 15 mA |
Maximum DC PV voltage | 450 V |
Start-up voltage | 120 V |
MPPT operating voltage range |
80 – 450 V (1)
|
Number of trackers | 4 |
Max. PV operational input current |
18 A per tracker
|
Max. PV short circuit current (2) |
20 A per tracker
|
Max. DC output charging power |
4000 W per tracker 11520 W total
|
Maximum PV array size per tracker (3) |
7200 Wp (450 V x 20 A) (3)
|
PV Isolation fail level (4) | 100 kΩ |
Synchronized Parallel Operation |
Yes, up to 25 units with VE.Can
|
Programmable relay (5) | Yes |
Protection |
PV reverse polarity Output short circuit Over temperature
|
Data communication |
VE.Direct port, VE.Can port & Bluetooth (6)
|
Bluetooth frequency |
2402 – 2480 MHz
|
Bluetooth power | 4dBm |
General purpose analogue/digital in port | Yes, 2x |
Remote on-off | Yes |
Operating temperature range |
-40 to +60 °C (fan assisted cooling)
|
Humidity (non-condensing) | max 95 % |
Material & Colour |
steel, blue RAL 5012
|
Protection category | IP21 |
Battery-connection | M8 bolt |
Power terminals PV input | 2 16 mm2 |
Weight | 13.7 kg |
Dimensions (h x w x d) in mm |
487 x 434 x 146
|
Safety |
EN-IEC 62109-1, EN-IEC 62109-2
|
Country of Origin |
Designed in The Netherlands, made in India
|
Please see more details in the 'Data Sheets' tab.
There is a 5 year replacement warranty on all Victron equipment (excluding batteries). Products will need to be delivered to an authorised technician to be inspected and evaluated.
Thanks for subscribing!
This email has been registered!